Is your glass window pane broken, cracked, or shattered? If yes, you should think about replacing it.
Besides facilitating aeration and lighting, window glasses are an aesthetic highlight for your home. Having damaged window panes can make your home look old and unsightly.
This is why you need a glass window pane replacement. It’ll not only improve boost the appearance of your home but also boost your property value.
But glass window pane replacement isn’t as straightforward as it sounds. Since the process is a bit technical and intimidating, here’s an easy-to-follow for your house window replacement.
When to Conduct Glass Window Pane Replacement
With home renovations being expensive and time-consuming, you may postpone replacing your house windows till it’s necessary. Here are instances when you should take on window glass replacement.
Foggy Windows
Are your windows frosting between the layers of glass?
It may be water condensing between the layers. This is usually caused by cracked window glass or broken seals that allow moisture between your glass panes.
Major Water Leakage
If you have excessive water entering your home through the window, the exterior window casing may be damaged. Before your whole house suffers from water damage, you should call in a glass window replacement technician from Renewal by Andersen Windows & Doors.
Cracked or Broken Panes
Damaged window glass panes are a potential hazard. You and your loved ones may get cuts or even a cold if you don’t react fast. Whether it’s the classic baseball through the window issue or an unfortunate burglary, you’ve got to get new window panes.
Drafty Windows
Have you noticed pockets of air rushing in and out of your home?
You may have a window with a draft. Not only is it uncomfortable but also increases your energy bills and risks your safety. A reputable glass replacement contractor will conduct a window glass pane assessment and fix your drafty windows in no time.
How to Replace a Window Glass Pane
Avoid a trip down to the repair shop and learn how to replace your window glass panes on your own. To understand the glass window pane replacement process, here’s a step-by-step guide.
Step 1: Remove the Damaged Pane
With your gloves and safety glasses, remove the glass shards from the frame one piece at a time. You may consider laying an old rag on the broken pane to help remove it easily and safely. In case some pieces aren’t loose enough, you may try to tap them with a hammer to create a new break line.
You can also apply duct tape to the pieces to remove them. Once you’re done removing the shards, dispose of them in a box so that they don’t hurt anyone.
Step 2: Measure the Window for the Replacement Glass
Using a tape measure, get the window pane dimensions. When measuring, ensure you start the measurement from the rough opening, starting with the width’s length first. Make sure you get accurate measurements. It helps you get the right-sized glass panes that fit your window.
If you are unsure about the measurements, consult a professional glass replacement professional for total peace of mind.
Step 3: Remove the Old Putty and Glazing
Scrape off the old putty from the window frame to create room for the new putty using a chisel. If the putty is so hard, you may need to use a heat gun to soften it or a hammer. But you need to tap the putty gently to avoid damaging the frame.
Since the grooves have to be smooth before fitting your new window, make sure you clean out the residue inside them.
Step 4: Fix the Rabbets
Take out old metal glazing points out of your rabbets and scrape them down until you reach bare wood. This preparation allows the new glass can fit well in it after replacement.
After the scrapping, apply the exterior primer on the wood using the brush. It’ll stop the bare wood from drawing oils out of the putty and shorten its life.
Step 5: Put the Putty in the Rabbets
Knead the putty until it’s warm and malleable and press it into the rabbets. Make sure the rabbets are full even if it looks messy or uneven.
Step 6: Put in the Glass
After pressing the putty into the rabbets, bed your glass pane into the frame. Ensure you apply little pressure on the glass using your fingertips until the glass is fully centered in the opening. In case you notice any voids developing under the glass, pull it out, add more putty, and repeat the process again.
Step 7: Install the Glazier Points
At the center of the windowpane, lay the glazier’s point flat on the glass and fit the putty knife’s tip against the raised shoulder points. While applying some downward pressure, slowly rock the point side to side until it seats well in the wood. You should then repeat the process on the other side. Afterward, you can scrape off the excess putty.
Step 8: Prepare a Putty Rope and Place It on the Frame
Roll some putty in your hands and make a rope around ¾ of an inch thick. You should apply the putty around the edges of the glass and press it down firmly against the rabbets. Fine-tune the putty so it doesn’t make your windows look messy.
Step 9: Prime the Frame and Paint It
Once your putty is hard enough, you can take some oil-based primer and paint it. You should first apply the primer and then coat the frame with paint until it’s even.
How Much Does It Cost to Replace Window Glass?
You can replace your glass window pane with about $150 to $650, without adding the labor costs. But window replacement costs vary, depending on your pane, window style, glass type, or window frame material.
Get Reliable and Stress-Free Glass Window Replacement Services
Want to hire dependable glass window pane replacement contractors?
You should assess your window replacement needs and conduct thorough research for the best contractors near you. For more articles about finances, health, fitness, and more, visit our website.
Leave a Reply